Snow Dyes Part 4

I so enjoyed doing all the test snow dyes, that I decided to go ahead and attempt to get the yellow to blue gradation I was hoping for our bedroom curtains. I had mixed the dye solution a few weeks ago and decided to use it the same way the first fabric was done, only I wanted to control the colors so they gradate from yellow to blue. Because of the size of the curtain panels, I decided to use a much larger plastic bin and layer them on top of one another with dye between each layer.

The next day, as I started rinsing the fabric, I knew it was too light, so I went right into an over-dye. I did this second one like the fourth "lasagna" fabric, using dye solution mixed in snow. I let the snow start melting on my printing table, and an hour later realized it was dripping all over the floor. Though I had intended to do each panel separately, I decided to layer them on top of one another so that the other panels could soak up all left-over dyed snow. The snow melted within an hour, and I decided to leave them to sit in the dye overnight. Today, they are still wet, so I think I will let them continue to dry out.

Here are views of the process:

Perhaps I will also post images once the panels are finished.

Snow Dyes Part 3

This is the third in a series of posts I've done on snow dyes this weekend. After about 7-8 hours in the basement studio yesterday, today I wanted to rinse out dyes and iron them. I hadn't really intended to do any new ones, but couldn't resist. It's not that we didn't have snow on the ground - there were already about 6 inches - but new snowfall through the course of the morning meant staying indoors and I had so much fun yesterday that I was bound to continue today. I made considerably more of a mess today, but what of it?

I believe I failed to note in my previous posts that I did not find any of the processes any more messy or difficult than the others, but I did find that I preferred the outcome of the dye solution mixed with the snow (see fabric #4), as it yielded more vibrant, darker colors and meant less time wearing a mask outside mixing the dye powder with the snow, which also yielded nice colors (see fabric #2).

Next, I combined a gradient technique that I use very often with snow dying. It is modified from Adrienne Buffington's "Luscious Berries" gradation.


Fabric Batch #5: (6-step progression dye solution in snow)
I set out six buckets and labeled them A-F then added 6 cups of snow to each. I soaked 6 half-yard pieces of pima cotton in a soda-ash solution. I mixed 1/2 T of Fuchsia in 1 c water and 1T Midnight Blue in 1 c water. I then mixed the colors as prescribed in Buffington's book, with the exception that I did not wait to add the second color. Both colors were added at the same time.

In buckets A-D the two colors were mixed into all 6 cups of snow then the fabric was gradually added, turning it over and mixing it all together so that the dyed snow was covering almost everywhere. (This was very messy and cold.) In buckets E-F I split the snow into two cups and each color was mixed separately. The fabric was put in lasagna layers with each color added to each layer. (Much less messy.)

The snow melted for about 8 hours, then I added warm water so that the fabric was totally submerged in each bucket. They sat overnight and were rinsed and ironed dry about 24 hours later.

All photos copyright Katrina Boles
Stay tuned for part 4...

Snow Dyes Part 2

As I mentioned in my previous post, I played in the snow, only in the sense that I used the snow to dye fabrics. In the first post, I showed my results from two techniques I found online. And now I will share two of my other trial techniques.


Fabric #3: (burried in snow)
One-half yard of pima cotton pre-soaked in soda ash solution. The fabric was put into a bucket with about 1-2 inches of snow, more snow was added on top. Then I dribbled an avocado dye solution (1/2 T dye in 1/2 c water) over the top of the snow. It was allowed to melt for 4.5 hours, until I dumped the rest of the snow and rinsed the fabric in synthrapol and ironed it dry. (Because of the lightness of the fabric in the result, I think perhaps allowing the snow to fully melt would make it darker, though perhaps either the total snow diluted the dye or the cold of the snow meant the dye was not heat-activated.)

Fabric 4: (lasagna snow dye)
One-half yard of pima cotton pre-soaked in soda ash solution. In a bucket with about 1 inch of snow at the bottom, I laid about 1/3 of the fabric flat on top. In a cup, I mixed two cups of snow with an amethyst solution of 1 tsp dye in 1/4 c water. I did the same with brilliant blue dye. Next, I added a bit of the snow-dye mixtures, and two Shakes cups worth of snow (about 4 measuring cups). I folded the fabric over and then added all of the amethyst snow-dye solution mixture and two more Shakes cups of snow. Lastly, I folded the last third of the fabric atop and added the brilliant blue snow-dye solution mixture and whatever was left of the amethyst and two more Shakes cups of snow. This was allowed to melt for 10 hours before rinsing and ironing dry.

All photos copyright Katrina Boles
Stay tuned for part 3...

Snow Dyes Part 1

Thursday when I trudged through the 6-8 inches of snow on my way to work I did not bother to think about what I might do with all this white stuff, aside from knowing I probably wouldn't be driving much until it was cleared.

But then, when I awoke on my Saturday morning, curious as to how I would fill my day (my art group get-together got postponed), it dawned on me that I might use the snow to do some much-postponed dyeing. It's been ages since I've been in my studio to do anything other than pilfer items like scissors or paper. All of a sudden, breakfast, showering, and other things of that nature flew from my mind as it raced through ideas of how I might use the snow. I decided the logical first step was to look up techniques that others have tried online. Most of the dyers I came across were placing their pre-soaked fabric on a raised surface, then piling on the snow, then the dye mixture. I also came across someone who tried mixing the powder dye with the snow, but found that to be rather messy.

I had some other ideas too... but I decided to start with the first two suggestions. Here's my process and my end results:

Fabric #1: (dye over snow)
First, I soaked a fat quarter of pima cotton in a soda-ash solution (no salt) for a few minutes as I stretched cheesecloth over a bucket. Then I laid out my cotton fabric, scrunching the edges to make it fit within the bucket's edges. Next I added about an inch of snow. Then I took 2Tbsp of cerulean (mixed five months ago to a solution of 1/2 T in 1/4 c water) and squirted it randomly atop the snow. I decided that left too much white space so I also did the same with cobalt (also mixed five months ago at the same ratio). I let this melt on it's own for four hours in my basement - at about 60 degrees - when I got impatient and took my embossing heat gun to it and melted the rest of the snow.

I rinsed with synthrapol and ironed it dry:

 

Fabric #2: (dye powder mixed into snow)

First I soaked a fat quarter of pima cotton in a soda ash solution for about one hour (I've found that the amount of soaking time really doesn't matter at all, that just happens to be how long it took for me to get test #1 and #2 started.) While the fabric was soaking, I mixed 1tsp Lemon Yellow into 2 cups of snow, 1tsp rust brown in 2 cups of snow, and 1 tsp dark brown into 2 cups of snow. On another bucket with cheesecloth stretched over the top, I laid out fabric #2, scrunching the edges again. Over the top of the fabric, sprinkled the dyed snow in a random pattern. It was left to melt in the basement for about four hours and then was rinsed with synthrapol and ironed dry.

A note about the colors in this second fabric: You will notice that there is green and a purple-ish color in this final fabric. That has to do with the dye mixes. In the Procion MX dyes (used here), rust brown and dark brown are not primary colors, they are a pre-mixture intended to give this color. I knew that this was likely to happen, as some dye particles will bleed out more than others. However, if you notice on the first sample this did not happen. That is because both cobalt and cerulean are primary colors, so they should be pure colors and the only mixing that should occur is between those two. Mixing non-primary colors can yield unintended, and sometimes very interesting results. However, if you are a dyer, and you want a very specific color, I would recommend using only the pure dyes and mixing them to get the color you need.

All photos copyright Katrina Boles

Stay tuned for part 2...

Blow Your Mind Animation

I shall say from the onset - so that no one gets the wrong idea - I did not find this video, it found me. By that, I mean that Mike sent me a link. And I was so blown away that I knew I just had to post it.


ShapeShifter from Charlex on Vimeo.

I haven't been doing 3D animation long enough to really even call myself a novice, but I think I can call myself an expert on watching animations since I have been doing that for nearly 30 years. And this is one of the most amazing 3D shorts I have come across.

Don't get me wrong, I really, really like all of the other 3D animations that I've referenced in my blog, but this one is flat-out stunning! Who needs the virtual 3D world that seems to be all the rage now, when there are people out there making the world break apart and put itself back together in 3D animation?

Progressive Animation...Again

As I continue to try and think my way through the creation of a progressive animation, I seem to keep coming back to the question of how do I create this thing without using 3D? I certainly could use Maya to create it, but that would take modeling a lot of aspects, which I probably don't have the time to do. So, once again, it's a question of how do I create a moving scene in 2D that is dynamic and illustrated beautifully? And...how do I do it all by myself?

Oh well I guess I'll have to invent my own wheel. Here's another beautiful animation by Psyop:


MTV HD Crow from mate on Vimeo.

Happiness

Since the new year began, I've done quite a bit of thinking and reading about what it makes to be happy. And though most of my conclusions are repetitions of previous epiphanies, I also realize that thinking about what makes us happy and reading about happiness is part of how I can become more positive. I came across this short movie and think it is so worth watching. (It doesn't hurt that TJ Thyne is in the starring role, and I think he is fabulous on Bones!)